ngHobbies
1.5W 1.3GHZ TRANSMITTER
Features:, Frequency Band:, 1280MHz Locked, Number of Channels:, 1, Audio Sub-carrier:, 5.5MHz, Transmission Range:, 1800 Meter plus, Power Consumption:, 600mA, Output Power:, 1500mW, Operation Voltage:, 12, Power Supply:, 12V/750mA, Antenna Connector:, SMA Connector, Weight:, 30 g, Dimensions:, 70 x 25.7 x 8 mm, Documentation:, , Warranty:, 3 months, Note:, ** The power level of this transmitter may be illegal in your country. Please check your local regulations and make sure you order this device only if you have the required licensing to use this product.,
Highly integrated 1.3 GHz transmitter. These transmitters are locked on ...ngHobbies
IPHONE INTERFACE CABLE
Weight | 15g |
Cable length | 2ft or about 60cm |
http | //www.immersionrc.com/itelemetry |
Specifications:, Plug and play with most receivers., Documentation:, Click here, iPhone Application:, ,
The iPhone interface cable is a companion to the EzOSD ...ngHobbies
EZUHF 8CH RECEIVER
Width | 28mm |
Height | 20mm |
Length | 70mm |
Weight | 20 grams (without antenna) |
Notice:, , Dimensions:, , Content of the pacakge:, 1 x EzUHF 8 channel Receiver, Note:, , Documentation:, , Support thread on RcGroups:,
The EzUHF 8-ch receiver which supports a diversity antenna configuration, ...ngHobbies
GOPRO CAMERA MOUNT FOR MK HEXA/OKTO
This GoPro Hero camera mount comes installed underneath, in the center of gravity of the Mikrokpter. It is also possible to install further to the front, so the wide angle of the GoPro will catch only minimal parts from the landing gear or the front outrigger. Installing it in such position we have achieved two important goals:, All motors work equally since nothing is off balance, Features:, Low cost, minimal parts. Pieces are CNC cut from 1.7mm G10/FR4, Package contains:, All necessary plates, screws, nuts and washers, Note:, Assembly required., Cables:, Do not forget to pick up a GoPro FPV cable from here:, GoPro Camera Cables, Demo Videos:, Outdoor testing - click here, Note:, This kit comes with a mounting plate which either replaces of can be sandwitched under the battery holding plate on Hexa and Optokopters. Additional mountig plates for Quads will be available soon., Assembly documentation:, Click here to open or download (2Mb),
New Generation Hobbies is proud to present this low cost ...ngHobbies
DRAGONOSD+ V2 COMBO
Width | 29mm |
Height | 12mm |
Length | 50mm |
Weight | 10 grams (OSD only) |
Display Features:, Voltage measurement:, 2 ports available, Current measurement:, 1 port available, GPS sensor provides:, Altitude, Ground speed, Coordinates, Number of satellites, Heading indicator, Home direction, LOS Distance, Distance to home, Barometric sensor provides:, Altitude, Temperature, Variometer:, Airspeed, Vertical speed indicator, Compass:, Magnetic heading indicator, IMU:, Artificial Horizont, Other features:, Elapsed time, Callsign, RSSI, Flight summary, Various display modes, Remote OSD off, Configurable border area, Configuration:, On screen menu, Configure via stick input, Configure via PC, Customizable screen layout, Alerts:, Range, Altitude, Stall speed, Voltage, mAh, Audio notification, Lost signal, RSSI level, Integration:, Single servo wire link from the DragonLink for multi-channel auto-pilot, Logging:, Google Earth Logging, Autopilot:, RTH (Return to home), IMU fly-by-wire, Wayppoints:, 20 GPS way points configurable on the PC, Hardware:, PAL/NTSC auto-detect, GPS auto-detect, UART interfaces, I2C extension bus (various devices supported), This OSD package contains the following items:, Main DragonOSD+ V2 board, Dimensions:, , Documentation:, Click here, Connection schematics:, Click Here, Firmware upgrades and download PC software:, Click here,
New Generation Hobbies is happy to bring you the new, ...ngHobbies
SKYWALKER FPV PAN/TILT POD KIT
Comes with a mounting plate that will fit many popular FPV cameras including | KX131, KX171, KX191, IF Cam, SN777, SN555 and many others |
Instructions to build the pan and tilt | Coming Soon |
Note:, careful routing of camera wiring is required to prevent binding during 180 degree or 360 degree operation., This kit will include*:, Laser cut components for the main pod, You'll need to supply:, Double sided servo tape to apply TX, camera, and tilt servo., Documentation:,
A SkyWalker FPV pod that uses a custom mechanism allowing ...ngHobbies
5VOLT 2 CHANNEL VIDEO SPLITTER V2
,
For the ultimate diversity system, New Generation Hobbies brings you ...ngHobbies
SKY SURFER FPV PAN/TILT POD KIT
Comes with a mounting plate that will fit many popular FPV cameras including | KX131, KX171, KX191, IF Cam, SN777, SN555 and many others |
Instructions to build the pan and tilt | Coming Soon |
Note:, careful routing of camera wiring is required to prevent binding during 180 degree or 360 degree operation., This kit will include*:, Laser cut components for the main pod, You'll need to supply:, Double sided servo tape to apply TX, camera, and tilt servo., Documentation:,
A Sky Surfer FPV pod that uses a custom mechanism ...ngHobbies
500MW LM 1.2GHZ TRANSMITTER
Please note: This product will not be sold/shipped to USA customers. Your order of the product will be cancelled and your payment refunded., Features:, Frequency Band:, 1200MHz, Number of Channels:, 6, Audio Sub-carrier:, 5.5MHz, Transmission Range:, 200-500 Meter, Power Consumption:, 450mA, Output Power:, 500mW, Operation Voltage:, 5-5.5V, Power Supply:, 5V/500mA, Antenna Connector:, SMA Connector, Weight:, 10 g, Dimensions:, 24 x 28 x 7 mm, Documentation:, , Warranty:, 6 months, Note:, The use and operation of this product will require a HAM or Amateur radio license., Important note for Canada customers:,
Highly integrated mini 1.2 GHz transmitter with well known quality ...ngHobbies
EZOSD
TV System | PAL or NTSC autodetect |
Width | 30mm |
Height | 17mm |
Length | 60mm |
Weight | 10 grams (OSD only) |
Features:, Crisp text, shadowed for better visibility, Dimensions:, , Documentation:, Manual, Connection schematics for 12V cameras:, Click Here, Upgrade and download software:, Click here,
New Generation Hobbies is happy to bring you the new, ...ngHobbies
GUARDIAN STABILIZATION EXPANDER FOR OSD PRO
Documentation:,
Feather-light and about the size of a postage stamp, the ...ngHobbies
GOPRO CAMERA MOUNT FOR MK HEXA/OKTO NO SERVOS
This GoPro Hero camera mount comes installed underneath, in the center of gravity of the Mikrokpter. It is also possible to install further to the front, so the wide angle of the GoPro will catch only minimal parts from the landing gear or the front outrigger. Installing it in such position we have achieved two important goals:, All motors work equally since nothing is off balance, Features:, Low cost, minimal parts. Pieces are CNC cut from 1.7mm G10/FR4, Package contains:, All necessary plates, screws, nuts and washers, Note:, Assembly required., Cables:, Do not forget to pick up a GoPro FPV cable from here:, GoPro Camera Cables, This GoPro Hero camera mount comes installed underneath, in the center of gravity of the Mikrokpter. It is also possible to install further to the front, so the wide angle of the GoPro will catch only minimal parts from the landing gear or the front outrigger. Installing it in such position we have achieved two important goals:, All motors work equally since nothing is off balance, Features:, Low cost, minimal parts. Pieces are CNC cut from 1.7mm G10/FR4, Package contains:, All necessary plates, screws, nuts and washers, Note:, Assembly required., Cables:, Do not forget to pick up a GoPro FPV cable from here:, GoPro Camera Cables, Demo Videos:, Outdoor testing - click here, Note:, This kit comes with a mounting plate which either replaces of can be sandwitched under the battery holding plate on Hexa and Optokopters. Additional mountig plates for Quads will be available soon., Assembly documentation:, Click here to open or download (2Mb),
New Generation Hobbies is proud to present this low cost ...ngHobbies
12/5VOLT 2 CHANNEL VIDEO SPLITTER V2
Manual:, Download here,
For the ultimate diversity system, New Generation Hobbies brings you ...